The group of oil seals used in dynamic applications include radial shaft seals that seal a rotating shaft around its circumference. They are also known as lip seals, but in this blog we will use the term oil seals.
If you are looking for more details, kindly visit NNK.
Usually, these oil seals are used to seal lubricating oil or grease and contain it within the application, so that moving parts such as bearings are continually supplied with enough lubrication. However, such seals are also used for sealing other liquids, gases, and solids, such as powders or granules.
All are fitted with a spring to preload the sealing lip. All these types are for non-pressurised or low-pressure applications up to 0.5 bar for diameters of a limited size. For diameter of 500 mm or more, the maximum pressure is 0.1 bar. For higher pressures, special types or PTFE lip seals can be used.
ERIKS type M (type B according to the DIN standard) has a single metal casing and rubber sealing lip. Since the casing is made of metal, it must be fitted in a well-finished, undamaged groove. Large volumes of oil seals with metal casings are often cheaper, which is why they are often used as original equipment in machines. However, if an oil seal has to be replaced, types with a rubber exterior (type R or RST) are easier to fit. Type MST is similar to M and commonly used. The difference is the dust lip in the MST oil seal that prevents dust and dirt reaching the sealing lip, and extends its service life in dusty environments.
ERIKS type GV (type C according to DIN) is equivalent to type M, but is a heavy-duty version with a double metal casing. This can be a useful solution with larger diameters in more demanding applications. There is also a version of this type with a dust lip; the GVST (type CS according to DIN).
ERIKS type R (type A according to the DIN standard) is identical in shape to type M, but has a rubber outer case with metal reinforcement on the inside. The rubber creates a good seal in the housing, even if the housing has suffered minor damage or is not in its best condition for other reasons. The RST version has a dust lip. These types are often chosen to replace a type with a metal outer case because they are easier to install and can cope with minor damage to the groove, such as scratches.
ERIKS also supplies the types GR and GRST. These are virtually identical to the types R and RST, except in this case the metal inner ring is also completely encased in rubber. ERIKS uses FKM rubber here as standard, so these seals are ideal for use in acidic environments.
An overview of the different standard types of oil seals and their main characteristics is shown below.
Outer case
The metal used in the outer case of oil seals is usually made of carbon steel. Upon request, and depending on quantities, a different type of steel (such as stainless steel) can be used.
The quality of the rubber or rubber fabric used to make an outer case is the same as the quality of the rubber sealing lip. Fabric reinforced rubber is, as the name suggests, rubber reinforced with a fabric.
Spring
Standard springs are made of carbon steel. We use stainless-steel springs for our GR and GRST oil seals made from FKM rubber. In some rare cases, an O-ring is even used as a spring element. Standard PTFE lip seals are not fitted with springs.
Sealing lip
The sealing lip is always made of a rubber or synthetic material. For oil seals with a rubber outer case (R, RST, GR, GRST), the rubber quality of the sealing lip and the outer case are the same.
The material of the sealing lip is chosen according to the liquid to be sealed and the rotational speed. For larger shafts, an NBR sealing lip can cope with surface speeds of up to 10-12 m/s, while an FKM lip is suitable for speeds of up to 35-38 m/s.
Nitrile Butadiene Rubber (NBR, nitrile)
NBR, also known as nitrile rubber or nitrile, is the most popular material for an oil seal because of its good resistance to many oils and greases, such as mineral grease and hydraulic oil. Depending on their composition, synthetic oils and greases, such as those based on glycol, can damage NBR rubber materials. Depending on the amount of glycol, a PTFE lip seal may be the best choice. NBR is also unable to cope with contact with acids and solvents. The rubber is suitable for oil and grease at temperatures from -35 °C to 100 °C.
Most ERIKS oil seals, such as the types M, MST, R and RST, are made of NBR as standard.
Fluorine rubber (FKM, Viton™)
FKM or FPM, which is in well-known brand Viton™, can withstand higher liquid temperatures of up to 180 ˚C. FKM is highly resistant to strong acids and bases, as well as to synthetic oils and greases. Glycol-based oil and grease, however, can also damage FKM.
Because of the higher temperature resistance of FKM, this material is also chosen for applications where higher speeds play a role, which raise the temperature at the sealing lip considerably. Usually, using FKM will result in a longer life than using NBR. This compensates the higher price of FKM compared to NBR, as an FKM does not have to be replaced as frequently. The low temperature resistance of standard FKM is limited to -15 ˚C.
If you are looking for more details, kindly visit gearbox oil seal factory.
Polytetrafluoroethylene (PTFE, Teflon®)
PTFE, which is used in the well-known brand Teflon®, is less commonly used, but it is the preferred material for specific rotating seals in the chemical, food and pharmaceutical industries. This material is notable for having a very low frictional resistance and the best chemical resistance. It can also withstand a very wide range of temperatures in these types of seals; -80 ˚C to 200 ˚C. The shafts on which oil seals with PTFE lips are used require a harder and finer finish. Something like an axle sleeve can also be used to meet this requirement.
EPDM
EPDM oil seals are less common. They are used in solvent, hot water and steam applications, EPDM resists low temperatures down to -50 °C and UV radiation well. Some types of EPDM are also suitable for higher temperatures up to +150 °C. EPDM oil seals are usually available upon request.
VMQ (silicone)
VMQ, also known as silicone, is also used for oil seals, but this is less common because the mechanical strength of VMQ is low and this material has poor wear-resistance This makes it less suitable for dynamic applications, but it can withstand fairly low and high temperatures from -60 °C to 200 °C. Many types of VMQ are also suitable for contact with pharmaceutical and food products, so VMQ is an option worth considering. VMQ oil seals are usually available on request.
To install an oil seal properly, the shaft must be undamaged. This is so the oil seal can do its job properly on the one hand, and to prevent it from being damaged during fitting on the other. In addition, it is very important to lubricate the shaft, the sealing lip and the bore with plenty of grease. This will allow the oil seal to slide more easily over the shaft and prevent dry running after the first rotation. The oil seal may also come into contact with the keyway, thread or other grooves when sliding over the shaft. By taping or covering the shaft at the location of these irregularities with oil-soaked paper, the oil seal can be mounted without damage to the sealing lip.
Other important factors are ensuring the hardness and roughness of the shaft are correct. A shaft hardness of HRC 45 is recommended for a rubber sealing lip, with a roughness of Ra 0.4-0.8. A higher shaft hardness of HRC 60 and shaft roughness of Ra 0.1-0.4 is recommended for a PTFE lip.
If you deal with rotatory shaft equipment, you would probably be having rubber seals in your mechanical assembly. For any manufacturing company, optimal functionality, efficiency, and long service life are essential to your success in the market. A component that is majorly underappreciated within a machine assembly, would be oil seal.
Shaft seals are used to prevent lubricant leaks like oil or grease and protect machinery from dirt, dust, and water—which makes them invaluable to industrial operations. In this post, we will dive deeper into oil seals and discuss everything that one must know, such as what it is, how it works, types, applications, and what to keep in mind when buying oil seals.
What are rubber oil seals?
Rubber oil seals are placed between moving and static parts of mechanical equipment to prevent damage caused by moisture, contaminants, etc. Also known as rotatory shaft seals, grease seals, fluid seals, lip seals, and dirt seals; oil seals play an important role in closing the gaps between moving and stationary parts of machines.
Their main purpose is to retain or separate fluids from mixing and escaping the gauge, as well as stop moisture, abrasives, corrosive materials, and foreign contaminants from entering the parts, thereby ensuring maximum machine efficiency. Moreover, shaft rubber seals help prevent lubricant leakage at high pressure, for instance, when the machine is working at an extremely high pace.
How does rubber oil seal work?
Oil seals work by retaining lubricant in a thin layer between the lip and the shaft. These seals are attached to the bearing, with their lip pressing against the rotating shaft and the casing resting against the housing to hold the seal in place.
Oil seals perform some functions that ensure functionality at all costs and they do this by retaining lubricants at all costs and not making them escape no matter how high the pressure is. Whenever an oil seal fails, it creates seal leakage allowing abrasives, corrosive moistures and sediments to enter machines. Oil seals are especially used in equipment that has rotating, oscillating, and reciprocating shafts – pumps, pistons, etc.
Different types of seals offered by rubber products manufacturers in India include – Single and double lip oil seals, metal cased, external and internal oriented oil seals, and spring-energized oil seals and you can pick the one that best suits your industry requirements.
Applications of Oil Seals
Practically, all machine equipment including assembled machines, car engines, and PTFE machined parts use these oil seals to prevent harmful interactions that could possibly result in damaged parts. They are used in the assembly of Elevators, conveyor belts, engines, grinding mills, pipelines, wind turbines, and more.
When equipment is under high pressure, lubricants tend to escape, and dry parts clash. Oil seals help prevent this by sealing holes where lubricants can leak out. rubber seals are designed to offer optimum sealing performance and extreme durability even under high-peripheral speed. They are lightweight, compact, and exhibit high self-lubricating properties. Oil seals are manufactured with high-grade materials and last long without showing any signs of hardening, softening, or aging.
Moreover, oil seals are widely used throughout the aerospace industry in both space exploration and aviation applications. Sujan Industries manufactures all aircraft rubber items including O-rings, Gaskets, Seals, Pistons, Grommets, Washers, and Protective Boots & Bellows. In the aviation sector, pneumatics and hydraulics are used to operate components like landing gear and wing flaps. Rubber gaskets are needed in these systems to keep dust and air out while ensuring aircraft components run effectively.
How to Choose the Right Oil Seal
Picking the right type of oil seals is crucial for the proper functioning of machines because in some situations not all types can fit to work on certain machines.
There are quite a few factors to put into consideration when you’re choosing the right oil seal for your machine. Some of these factors include – dimensions, pressure, temperature, type of fluid, lubricant, shaft speed, shaft and bore tolerance, and more.
The capacity of oil seals to handle different intensities of pressure varies with their composition and application, so it is important to understand the compression set of your equipment. Just like the pressure, the temperature that your oil seal will be operating in must be known to be able to choose one that can withstand the working temperature.
Likewise, different types of fluids like grease, water, oil, fuels, etc. will come into contact with oil seals. So, knowing what type of fluids will be in constant contact with oil seals will help you choose the one capable of withstanding the surrounding conditions. When we talk about lubricants, seals always perform well when lubricated, however, in some machines there are dry spells. If you are a supplier of aftermarket parts in India or a user looking for oil seals in the aerospace industry, your search might end with Sujan Industries.
Wrapping Up
Comments
Please Join Us to post.
0